معالجة التشققات للمقاطع النحاسية باستخدام المعاملة الحرارية
Treating the Cracks of Copper Sections Under the Effect of Heat Treatment
Abstract
أوضحت نَتائِجَ هذا البحثِ بأنّ المعاَملة الحراريةَ لسبيكة النحاس-قصدير المستخدمة في البحث بدرجة (900)º م لمدة (15) دقيقة ، مع التقسية بالماءِ, ومن ثم إعادة التسخين بدرجة (600)ºم لمدة (3) ساعات, أعطت أفضل الخصائص الميكانيكيةِ ،المتضمنة على, مقاومة الشدّ، المتانة، قابلية التشكيل, بسبب البنية المجهرية الدقيقة والتوزيع المتجانس للأطوار ضمن أرضية التركيب, مما يقود إلى تأثير قوي على الخواص الميكانيكية.
The results of this research show that the heat treatment of the Copper-Tin alloy which used in this research with (900) °C at (15) min, with quenching in water, and reheating with (600) °C at (3) hours lead to best the mechanical properties, which include, tensile strength, toughness, Formability, because of a microstructure in which the fine phase is well dispersed uniformly in the matrix which leads to a remarkable reinforcement effect on mechanical properties.
Downloads
References
S.Sayar,( Heat Transfer During Melting and Solidification In Heterogeneous Materials) M.Sc. Thesis Mech. Eng. Univ. of Virginia Polytechnic Virginia ,2000.
F.M.Kotlyayrski and V.I.Belik (Effect of Heat Removal Rates on Formation of Silurian Casting ) , Liteinoe. Proizvadstvo , 1990, No.6 , P.10-12.
K.M.Daws , (Computer Simulation For Casting Mould Design ) Ph.D. Thesis, Mach. Eng. ,Univ. of Baghdad, Baghdad ,1997.
K.Y.Lee , S.M.Lee and C.P.Hong ,(Modeling of Fluid Flow and Solidification Grain Structures of AL-Cu Crystalline Ribbons in Planar Flow Casting) 2001.
J.A.Dantzig (Molding Solidification Processes Using FIDAP, Crystal. Res. Technol.1999 ,Vol.34 ,P. 417-424.
S.G.Humberto and D.F.Osmario, (Simulation of the Mushy Zone Solidification of a Binary Alloy) ,2000 , European Congress on Computational Methods in Applied Sciences and Engineering, Barcelona, September, P.1-12.
A.K.Singh , R.Pardeshi and B.Bash, (Modeling of Convection During Solidification of Metal ) , Sadhana ,2001, Vol.26. part 1&2 February-April, P.139-162.
Yaping Wu, (Numerical Analysis of Direct-Chill Casting of AL Ingot) , M.Sc., Thesis , Mech. And Aerospace Eng. ,Univ. of West Virginia, West Virginia, 1999.
V.A.Efimov, (Influence of Connective Heat and Mass Transfer on Casting Formation ), 1990, Liteinone. Proi. Zvodstvo, No.11, P. 1-8.
Y.Kamotani, F.B.Weng and S.Ostrach (Oscillatory Natural Convocation of a Liquid Metal in Circular Cylinder ) 1999, Journal of Heat Transfer, Vol. 116, August , P.627-632.
Published
How to Cite
Issue
Section
Copyright (c) 2010 Mostafa Ahmed Rijab, Alaa Ahmed Majeed
This work is licensed under a Creative Commons Attribution 4.0 International License.