Cooling High Power Microchip Using Metallic Porous Heat Sink
DOI:
https://doi.org/10.24237/djes.2025.18106Keywords:
High-power microchip, Porous metallic media, Heat sink, Numerical analysisAbstract
Modern living and technological advancements demand high-power microchips, leading to an increase in chip surface temperatures. To mitigate this heat, porous metallic heat sinks are employed. This study presents a simulation of a high-power microprocessor (>10⁴ W/m²) encased in a porous metallic heat sink. The microchip measures 4 cm in diameter with a thickness of 5 mm. The governing equations are solved numerically using the finite element method, implemented in COMSOL Multiphysics software. This paper investigates the cooling performance of a microchip through natural convection, focusing on three key parameters: aspect ratio, porosity, and heat sink material. The study considers heat sink porosities of 0.2, 0.4, and 0.8; aspect ratios of 0.2, 0.5, 1, and 2; and heat sink materials including copper, aluminium, and steel. Results are presented as temperature and Nusselt number contours on the microchip's surface. The findings indicate that copper achieves the lowest surface temperature (41.58℃) and the highest Nusselt number (243.81) at an aspect ratio of 2. Increasing the aspect ratio enhances the heat transfer rate and, consequently, the Nusselt number. Conversely, steel exhibits the highest surface temperature (89.35℃), the lowest heat transfer coefficient (164.89 W/m·K), and the lowest Nusselt number (62.84).
Downloads
References
[1] L. Gong, Y. Li, Z. Bai, and M. Xu, "Thermal performance of micro-channel heat sink with metallic porous/solid compound fin design," Applied Thermal Engineering, vol. 137, pp. 288-295, 2018.
[2] N. Habib and M. Tahir, "Thermal analysis of proposed heat sink design under natural convection for the thermal management of electronics," Thermal Science, vol. 26, no. 2 Part, pp. 1487-1501, 2022.
[3] A. Zehri et al., "High porosity and light weight graphene foam heat sink and phase change material container for thermal management," Nanotechnology, vol. 31, no. 42, p. 424003, 2020.
[4] E. M. Abo-Zahhad et al., "A Micro-Metal Inserts Based Microchannel Heat Sink for Thermal Management of Densely Packed Semiconductor Systems," Sustainability, vol. 14, no. 21, p. 14182, 2022.
[5] C. S. Sharma, G. Schlottig, T. Brunschwiler, M. K. Tiwari, B. Michel, and D. Poulikakos, "A novel method of energy efficient hotspot-targeted embedded liquid cooling for electronics: An experimental study," International Journal of Heat and Mass Transfer, vol. 88, pp. 684-694, 2015.
[6] X. Chen, H. Ye, X. Fan, T. Ren, and G. Zhang, "A review of small heat pipes for electronics," Applied Thermal Engineering, vol. 96, pp. 1-17, 2016.
[7] A. Arshad, H. M. Ali, W.-M. Yan, A. K. Hussein, and M. Ahmadlouydarab, "An experimental study of enhanced heat sinks for thermal management using n-eicosane as phase change material," Applied Thermal Engineering, vol. 132, pp. 52-66, 2018.
[8] A. Kabeel, M. Mousa, M. M. Abdelaziz, R. Sathyamurthy, and M. Abdelgaied, "Performance of the novel design thermoelectric cooling system," Heat Transfer, vol. 49, no. 8, pp. 4134-4152, 2020.
[9] M. A. Khan, H. M. Ali, T. u. Rehman, A. Arsalanloo, and H. Niyas, "Composite pin‐fin heat sink for effective hotspot reduction," Heat Transfer, vol. 53, no. 4, pp. 1816-1838, 2024.
[10] M. Hameed, H. N. Mohammed, and M. R. Abdullah, "The Improving the Thermal Performance of a Heat Exchanger using a New Passive Technology," Tikrit Journal of Engineering Sciences, vol. 30, no. 1, pp. 66-71, 2023.
[11] T. K. Ibrahim, A. T. Al-Sammarraie, W. H. Al-Taha, M. R. Salimpour, M. Al-Jethelah, A. N. Abdalla, and H. Tao, "Experimental and numerical investigation of heat transfer augmentation in heat sinks using perforation technique," Applied Thermal Engineering, vol. 160, p. 113974, 2019.
[12] T. K. Ibrahim, A. T. Al-Sammarraie, M. S. Al-Jethelah, W. H. Al-Doori, M. R. Salimpour, and H. Tao, "The impact of square shape perforations on the enhanced heat transfer from fins: Experimental and numerical study," International Journal of Thermal Sciences, vol. 149, p. 106144, 2020.
[13] A. K. PV, G. C. AC, and P. M. Kamath, "Heat transfer enhancement of electronic chip cooling using porous medium," in ASME Heat and Mass Transfer Conference, 2013.
[14] D. A. Nield and A. Bejan, Convection in porous media. New York: Springer, 2013.
[15] T. K. Ibrahim, F. Basrawi, M. N. Mohammed, and H. Ibrahim, "Effect of perforation area on temperature distribution of the rectangular fins under natural convection," ARPN Journal of Engineering and Applied Sciences, vol. 11, no. 10, pp. 6371-6375, 2016.
[16] T. K. Ibrahim et al., "Experimental study on the effect of perforations shapes on vertical heated fins performance under forced convection heat transfer," International Journal of Heat and Mass Transfer, vol. 118, pp. 832-846, 2018.
[17] M. Zaretabar, H. Asadian, and D. Ganji, "Numerical simulation of heat sink cooling in the mainboard chip of a computer with temperature dependent thermal conductivity," Applied Thermal Engineering, vol. 130, pp. 1450-1459, 2018.
[18] Y. J. Lee and S. J. Kim, "Thermal optimization of the pin-fin heat sink with variable fin density cooled by natural convection," Applied Thermal Engineering, vol. 190, p. 116692, 2021.
[19] H.-T. Chen, P.-L. Chen, J.-T. Horng, and Y.-H. Hung, "Design optimization for pin-fin heat sinks," 2005.
[20] D. Yang, Y. Wang, G. Ding, Z. Jin, J. Zhao, and G. Wang, "Numerical and experimental analysis of cooling performance of single-phase array microchannel heat sinks with different pin-fin configurations," Applied Thermal Engineering, vol. 112, pp. 1547-1556, 2017.
[21] J. Zhao, S. Huang, L. Gong, and Z. Huang, "Numerical study and optimizing on micro square pin-fin heat sink for electronic cooling," Applied Thermal Engineering, vol. 93, pp. 1347-1359, 2016.
[22] P. Smakulski and S. Pietrowicz, "A review of the capabilities of high heat flux removal by porous materials, microchannels and spray cooling techniques," Applied thermal engineering, vol. 104, pp. 636-646, 2016.
[23] L. Gong, J. Zhao, and S. Huang, "Numerical study on layout of micro-channel heat sink for thermal management of electronic devices," Applied Thermal Engineering, vol. 88, pp. 480-490, 2015.
[24] T.-C. Hung, Y. Hung, and W.-M. Yan, "Design of Porous-Microchannel heat sinks with different porous configurations," International Journal of Materials, Mechanics and Manufacturing, vol. 4, no. 2, pp. 89-94, 2016.
[25] T.-C. Hung, Y.-X. Huang, and W.-M. Yan, "Thermal performance analysis of porous-microchannel heat sinks with different configuration designs," International Journal of Heat and Mass Transfer, vol. 66, pp. 235-243, 2013.
[26] T.-C. Hung and W.-M. Yan, "Thermal performance enhancement of microchannel heat sinks with sintered porous media," Numerical Heat Transfer, Part A: Applications, vol. 63, no. 9, pp. 666-686, 2013.
[27] H. M. Ali, A. Arshad, M. Jabbal, and P. G. Verdin, "Thermal management of electronics devices with PCMs filled pin-fin heat sinks: a comparison," International Journal of Heat and Mass Transfer, vol. 117, pp. 1199-1204, 2018.
[28] M. Al-Jethelah, H. Dheyab, S. Khudhayer, T. Ibrahim, and A. Al-Sammarraie, "Latent heat storage for hot beverages," Journal of Mechanical Engineering and Sciences, vol. 13, no. 3, pp. 5653-5664, 2019.
[29] M. Arqam, L. S. Raffa, L. Clemon, M. S. Islam, M. Ryall, and N. S. Bennett, "Numerical and experimental investigation of a phase change material radial fin heat sink for electronics cooling," Journal of Energy Storage, vol. 98, p. 113113, 2024.
[30] M. Motevalizadeh, A. Rooberahan, M. S. Namaghi, M. Mohammadi, M. Passandideh-Fard, and M. Sardarabadi, "Cooling enhancement of portable computers processor by a heat pipe assisted with phase change materials," Journal of Energy Storage, vol. 56, p. 106074, 2022.
[31] R. Singh, A. Akbarzadeh, and M. Mochizuki, "Sintered porous heat sink for cooling of high-powered microprocessors for server applications," International Journal of Heat and Mass Transfer, vol. 52, no. 9-10, pp. 2289-2299, 2009.
[32] R. Rachedi and S. Chikh, "Enhancement of electronic cooling by insertion of foam materials," Heat and Mass Transfer, vol. 37, no. 4-5, pp. 371-378, 2001.
[33] K.-H. Ko and N. Anand, "Use of porous baffles to enhance heat transfer in a rectangular channel," International Journal of Heat and Mass Transfer, vol. 46, no. 22, pp. 4191-4199, 2003.
[34] S. Y. Kim, J. W. Paek, and B. H. Kang, "Thermal performance of aluminum-foam heat sinks by forced air cooling," IEEE Transactions on components and packaging technologies, vol. 26, no. 1, pp. 262-267, 2003.
[35] A. Bhattacharya and R. Mahajan, "Metal foam and finned metal foam heat sinks for electronics cooling in buoyancy-induced convection," 2006.
[36] W. Hsieh, J. Wu, W. Shih, and W. Chiu, "Experimental investigation of heat-transfer characteristics of aluminum-foam heat sinks," International Journal of Heat and Mass Transfer, vol. 47, no. 23, pp. 5149-5157, 2004.
[37] K. Leong and L. Jin, "Effect of oscillatory frequency on heat transfer in metal foam heat sinks of various pore densities," International journal of heat and mass transfer, vol. 49, no. 3-4, pp. 671-681, 2006.
[38] C. T. DeGroot, A. G. Straatman, and L. J. Betchen, "Modeling forced convection in finned metal foam heat sinks," 2009.
[39] Q. Wang, X. Han, A. Sommers, Y. Park, C. T'Joen, and A. Jacobi, "A review on application of carbonaceous materials and carbon matrix composites for heat exchangers and heat sinks," International journal of refrigeration, vol. 35, no. 1, pp. 7-26, 2012.
[40] Y. Ould-Amer, S. Chikh, K. Bouhadef, and G. Lauriat, "Forced convection cooling enhancement by use of porous materials," International Journal of Heat and Fluid Flow, vol. 19, no. 3, pp. 251-258, 1998.
[41] M. E. Skuntz, R. Elander, M. Al Azawii, P. Bueno, and R. Anderson, "System efficiency of packed bed TES with radial flow vs. axial flow–Influence of aspect ratio," Journal of Energy Storage, vol. 72, p. 108463, 2023.
[42] Ashrae, ASHRAE Pocket Guide for Air Conditioning, Heating, Ventilation, Refrigeration. ASHRAE, 2018.
[43] F. P. Incropera, Fundamentals of heat and mass transfer, 6th ed. / Frank P. Incropera ... [et al.].. ed. Hoboken, NJ: Hoboken, NJ : John Wiley, 2007.
[44] D. R. Pitts and L. E. Sissom, "Schaum's outline of theory and problems of heat transfer," Second Edition, 1998.
[45] M. Fenni, M. Guellal, and S. Hamimid, "Influence of porosity properties on natural convection heat transfer in porous square cavity," Physics of Fluids, vol. 36, no. 5, 2024.
Downloads
Published
Issue
Section
License
Copyright (c) 2025 Sabah F. H. Alhamdi, Mohammad M. S. Al-Azawii, Ahmed K. Alshara
This work is licensed under a Creative Commons Attribution 4.0 International License.
