Investigate the Impact of PCM on the Thermal Performance of a Building Wall Under Hot Climates
DOI:
https://doi.org/10.24237/djes.2025.18109Keywords:
Thermal energy storage, Heat gain, PCM, Air conditioningAbstract
Southern Iraq, specifically Basrah, has a warm and arid climate. August has the greatest average temperatures in Basrah, with highs of 48°C. To overcome obstacles resulting from such major temperatures, Phase Change Materials (PCMs) are increasingly being used in building construction. This paper performed an experimental study to examine the energy efficiency of building walls that integrated with PCM under Iraq conditions. Additionally, the thermal performance of two different building walls was compared. The parameters investigated include the influence of heat gain, PCM temperature, and thermal load levelling (TLL) for both PCM and cement cases. Two test cases were exanimations. In the first case, the wall is made of blocks with cement filled holes. In the second case, the wall is made of blocks with PCM filling the holes. The outside conditions are controlled by using the hot water tank, and the cold-water tank represents the inside conditions for air conditioning space. The experimental analysis indicated that building blocks filled with PCM case achieve lower interior temperature and heat gain than cement case blocks. Furthermore, the peak heat flow was decreased by 75% when PCM-filled blocks were used instead of cement-filled blocks. The results revealed that PCM significantly minimize TLL by 42.6% as compared to cement. In conclusion, when the PCM is used to replace the cement, the interior thermal comfort improved and cooling energy use reduced.
Downloads
References
[1] A. Lateef Tarish, M. Talib Hamzah, and W. Assad Jwad, “Thermal and exergy analysis of optimal performance and refrigerant for an air conditioner split unit under different Iraq climatic conditions,” Therm. Sci. Eng. Prog., vol. 19, no. June, p. 100595, 2020, doi: 10.1016/j.tsep.2020.100595.
[2] A. H. N. Al-mudhafar, M. T. Hamzah, and A. L. Tarish, “Potential of integrating PCMs in residential building envelope to reduce cooling energy consumption,” Case Stud. Therm. Eng., vol. 27, no. July, p. 101360, 2021, doi: 10.1016/j.csite.2021.101360.
[3] M. Saffari, A. de Gracia, S. Ushak, and L. F. Cabeza, “Passive cooling of buildings with phase change materials using whole-building energy simulation tools: A review,” Renew. Sustain. Energy Rev., vol. 80, no. January, pp. 1239–1255, 2017, doi: 10.1016/j.rser.2017.05.139.
[4] Al-Mudhafar, Ahmed HN, and Ali Lateef Tarish. "Enhancing PCM melting in a triple tube heat exchanger by utilizing innovative fins configurations." Journal of the Brazilian Society of Mechanical Sciences and Engineering 46, no. 5 (2024): 262.
[5] R. Abdulrahman, F. Ibrahim, A. Al-Mudhafar, and S. Dakhil, “Numerical study of PCM melting processes in trapezoidal channel,” J. Phys. Conf. Ser., vol. 1773, no. 1, 2021, doi: 10.1088/1742-6596/1773/1/012017.
[6] A. H. N. Al-Mudhafar, A. F. Nowakowski, and F. C. G. A. Nicolleau, “Performance enhancement of PCM latent heat thermal energy storage system utilizing a modified webbed tube heat exchanger,” Energy Reports, vol. 6, pp. 76–85, 2020, doi: 10.1016/j.egyr.2020.02.030.
[7] K. O. Lee, M. A. Medina, E. Raith, and X. Sun, “Assessing the integration of a thin phase change material (PCM) layer in a residential building wall for heat transfer reduction and management,” Appl. Energy, vol. 137, pp. 699–706, 2015, doi: 10.1016/j.apenergy.2014.09.003.
[8] F. Kuznik, D. David, K. Johannes, and J. J. Roux, “A review on phase change materials integrated in building walls,” Renew. Sustain. Energy Rev., vol. 15, no. 1, pp. 379–391, 2011, doi: 10.1016/j.rser.2010.08.019.
[9] S. A. Memon, “Phase change materials integrated in building walls: A state of the art review,” Renew. Sustain. Energy Rev., vol. 31, pp. 870–906, 2014, doi: 10.1016/j.rser.2013.12.042.
[10] B. Lamrani, K. Johannes, and F. Kuznik, “Phase change materials integrated into building walls: An updated review,” Renew. Sustain. Energy Rev., vol. 140, no. June 2020, p. 110751, 2021, doi: 10.1016/j.rser.2021.110751.
[11] Y. Cui, J. Xie, J. Liu, and S. Pan, “Review of Phase Change Materials Integrated in Building Walls for Energy Saving,” Procedia Eng., vol. 121, pp. 763–770, 2015, doi: 10.1016/j.proeng.2015.09.027.
[12] R. Barzin, J. J. J. Chen, B. R. Young, and M. M. Farid, “Application of PCM energy storage in combination with night ventilation for space cooling,” Appl. Energy, vol. 158, pp. 412–421, 2015, doi: 10.1016/j.apenergy.2015.08.088.
[13] X. Mi, R. Liu, H. Cui, S. A. Memon, F. Xing, and Y. Lo, “Energy and economic analysis of building integrated with PCM in different cities of China,” Appl. Energy, vol. 175, pp. 324–336, 2016, doi: 10.1016/j.apenergy.2016.05.032.
[14] R. Ansuini, R. Larghetti, A. Giretti, and M. Lemma, “Radiant floors integrated with PCM for indoor temperature control,” Energy Build., vol. 43, no. 11, pp. 3019–3026, 2011, doi: 10.1016/j.enbuild.2011.07.018.
[15] P. Marin et al., “Energy savings due to the use of PCM for relocatable lightweight buildings passive heating and cooling in different weather conditions,” Energy Build., vol. 129, pp. 274–283, 2016, doi: 10.1016/j.enbuild.2016.08.007.
[16] R. A. Kishore, M. V. A. Bianchi, C. Booten, J. Vidal, and R. Jackson, “Optimizing PCM-integrated walls for potential energy savings in U.S. Buildings,” Energy Build., vol. 226, p. 110355, 2020, doi: 10.1016/j.enbuild.2020.110355.
[17] Y. Hamidi, Z. Aketouane, M. Malha, D. Bruneau, A. Bah, and R. Goiffon, “Integrating PCM into hollow brick walls: Toward energy conservation in Mediterranean regions,” Energy Build., vol. 248, p. 111214, 2021, doi: 10.1016/j.enbuild.2021.111214.
[18] M. Mahdaoui et al., “Building bricks with phase change material (PCM): Thermal performances,” Constr. Build. Mater., vol. 269, p. 121315, 2021, doi: 10.1016/j.conbuildmat.2020.121315.
[19] M. Jaworski, “Thermal performance of building element containing phase change material (PCM) integrated with ventilation system - An experimental study,” Appl. Therm. Eng., vol. 70, no. 1, pp. 665–674, 2014, doi: 10.1016/j.applthermaleng.2014.05.093.
[20] U. Stritih, V. V. Tyagi, R. Stropnik, H. Paksoy, F. Haghighat, and M. M. Joybari, “Integration of passive PCM technologies for net-zero energy buildings,” Sustain. Cities Soc., vol. 41, pp. 286–295, 2018, doi: 10.1016/j.scs.2018.04.036.
[21] M. Salihi et al., “Evaluation of global energy performance of building walls integrating PCM: Numerical study in semi-arid climate in Morocco,” Case Stud. Constr. Mater., vol. 16, no. February, p. e00979, 2022, doi: 10.1016/j.cscm.2022.e00979.
[22] R. J. Khan, M. Z. H. Bhuiyan, and D. H. Ahmed, “Investigation of heat transfer of a building wall in the presence of phase change material (PCM),” Energy Built Environ., vol. 1, no. 2, pp. 199–206, 2020, doi: 10.1016/j.enbenv.2020.01.002.
[23] Rahi, Mohammed Fareed, et al. "Numerical investigation and optimization of macro-encapsulated phase change material capsules in building roof slab." Journal of Energy Storage 68 (2023): 107806. https://doi.org/10.1016/j.est.2023.107806.
[24] Song, Haemin, et al. "Proposed specific heat capacity model for a concrete wall containing phase change material (PCM) under field experiment conditions." Construction and Building Materials 336 (2022): 127381.
[25] Zhang, Guixiao, et al. "Thermal performance of a novel building wall incorporating a dynamic phase change material layer for efficient utilization of passive solar energy." Construction and Building Materials 317 (2022): 126017.
[26] Zhang, Yichao, et al. "Thermal insulation performance of buildings with phase-change energy-storage wall structures." Journal of Cleaner Production 438 (2024): 140749.
[27] Ahmed, H. Naseer. "Energy Consumption Optimization for Residential Buildings in Basrah City", M.sc, thesis, University of Basrah, 2009.
[28] https://www.weather-atlas.com/en/iraq/basrah-climate
[29] Ozel, M., and K. Pihtili. "Investigation of the most suitable location of insulation applying on building roof from maximum load levelling point of view." building and environment 42.6 (2007): 2360-2368.
[29] Ravelo, Blaise, Lala Rajaoarisoa, and Olivier Maurice. "Thermal modelling of multilayer walls for building retrofitting applications." Journal of Building Engineering 29 (2020): 101126.
[30] Islam, Md Nahidul, Md Nahid Hossain, and Dewan Hasan Ahmed. "Investigation of phase-change materials for interior temperature regulation in public transport." Clean Energy 6.1 (2022): 178-192.
[31] Rathore, Pushpendra Kumar Singh, and Shailendra Kumar Shukla. "Enhanced thermophysical properties of organic PCM through shape stabilization for thermal energy storage in buildings: A state of the art review." Energy and Buildings 236 (2021): 110799.
Downloads
Published
Issue
Section
License
Copyright (c) 2025 Ahmed H. N. Al-Mudhafar, Ali Lateef Tarish, Akeel M. Ali Morad
This work is licensed under a Creative Commons Attribution 4.0 International License.
