Thermal Performance Analysis of U-pipe Evacuated Tube Solar Heater System with and without PCM

Salah Noori ALali; Jasim  Abdulateef; Qusay Hassan; Marek Jaszczur

doi:10.24237/djes.2023.160403

Authors

Salah Noori ALali
eng_grad_mech002@uodiyala.edu.iq
Department of Mechanical Engineering, University of Diyala, 32001 Diyala, Iraq
Jasim Abdulateef Department of Mechanical Engineering, University of Diyala, 32001 Diyala, Iraq
Qusay Hassan Department of Mechanical Engineering, University of Diyala, 32001 Diyala, Iraq
Marek Jaszczur AGH University of Science and Technology, Faculty of Energy and Fuels, Krakow, Poland

Keywords:

Solar heater, Evacuated tube, PCM, Solidification, Useful energy

Abstract

The study presents a comprehensive thermal performance analysis of a U-pipe Evacuated Tube Solar Collector (U-ETSC) system, integrated with Phase Change Material (PCM), for satisfying water demand in domestic applications. The innovative approach of incorporating PCM aims to enhance the system's efficiency during night or off-sunny hours, addressing a common limitation in solar heater systems. The research primarily focuses on the impact of varying mass flow rates of the heat transfer fluid (HTF) on the thermal dynamics of the system. Experimental results reveal that as the mass flow rates of HTF increase from 0.5 to 1 and then to 1.5 liters per minute, there is a notable change in the phase transition times of the PCM. Specifically, the melting time of the PCM is increased by 13% and 16% for the respective flow rates, suggesting a delayed response in energy absorption. Conversely, the solidification time of the PCM is reduced by 16% and 18% respectively, indicating a faster release of stored thermal energy. This behavior underscores the PCM's significant role in stabilizing the system's thermal output during varying solar intensities. The findings of this study highlight the potential of integrating PCM in U-ETSC systems to achieve a more consistent and reliable supply of hot water for domestic purposes, especially during periods when solar irradiance is low or absent.

Downloads

Download data is not yet available.

References

Suman, S., Khan, M. K., & Pathak, M. (2015). Performance enhancement of solar collectors—A review. Renewable and Sustainable Energy Reviews, 49, 192-210. DOI: https://doi.org/10.1016/j.rser.2015.04.087

O’Neil, T. J., & Sobhansarbandi, S. (2022). Thermal performance investigation of energy storage-based U-pipe evacuated tube solar collector: An experimental study. Sustainable Energy Technologies and Assessments, 52, 102146. DOI: https://doi.org/10.1016/j.seta.2022.102146

Alshukri, M. J., Eidan, A. A., & Najim, S. I. (2021). Thermal performance of heat pipe evacuated tube solar collector integrated with different types of phase change materials at various location. Renewable Energy, 171, 635-646. DOI: https://doi.org/10.1016/j.renene.2021.02.143

Chopra, K., Pathak, A. K., Tyagi, V. V., Pandey, A. K., Anand, S., & Sari, A. (2020). Thermal performance of phase change material integrated heat pipe evacuated tube solar collector system: An experimental assessment. Energy Conversion and Management, 203, 112205. DOI: https://doi.org/10.1016/j.enconman.2019.112205

Essa, M. A., Rofaiel, I. Y., & Ahmed, M. A. (2020). Experimental and theoretical analysis for the performance of evacuated tube collector integrated with helical finned heat pipes using PCM energy storage. Energy, 206, 118166. DOI: https://doi.org/10.1016/j.energy.2020.118166

Li, Y., Liang, X., Song, W., Li, T., Wang, D., & Liu, Y. (2022). Optimization and thermal performance of U-type evacuated tube solar collector filled with phase change material. Energy Reports, 8, 6126-6138. DOI: https://doi.org/10.1016/j.egyr.2022.04.054

Algarni, S., Mellouli, S., Alqahtani, T., Almutairi, K., & Anqi, A. (2020). Experimental investigation of an evacuated tube solar collector incorporating nano-enhanced PCM as a thermal booster. Applied Thermal Engineering, 180, 115831. DOI: https://doi.org/10.1016/j.applthermaleng.2020.115831

Pathak, S. K., Tyagi, V. V., Chopra, K., & Sari, A. (2023). Thermal performance and design analysis of U-tube based vacuum tube solar collectors with and without phase change material for constant hot water generation. Journal of Energy Storage, 66, 107352. DOI: https://doi.org/10.1016/j.est.2023.107352

Chopra, K., Tyagi, V. V., Pathak, A. K., Pandey, A. K., & Sari, A. (2019). Experimental performance evaluation of a novel designed phase change material integrated manifold heat pipe evacuated tube solar collector system. Energy Conversion and Management, 198, 111896. DOI: https://doi.org/10.1016/j.enconman.2019.111896

Olfian, H., Ajarostaghi, S. S. M., Ebrahimnataj, M., Farhadi, M., & Arıcı, M. (2022). On the thermal performance of evacuated tube solar collector integrated with phase change material. Sustainable Energy Technologies and Assessments, 53, 102437. DOI: https://doi.org/10.1016/j.seta.2022.102437

Uniyal, A., & Prajapati, Y. K. (2022). Thermal Performance Study of a Copper U-Tube-based Evacuated Tube Solar Water Heater. Energy Conversion and Green Energy Storage, 101-114. DOI: https://doi.org/10.1201/9781003258209-7

Kumar, A., Tiwari, A. K., & Said, Z. (2021). A comprehensive review analysis on advances of evacuated tube solar collector using nanofluids and PCM. Sustainable Energy Technologies and Assessments, 47, 101417. DOI: https://doi.org/10.1016/j.seta.2021.101417

Pawar, V. R., & Sobhansarbandi, S. (2023). Heat transfer enhancement of a PCM-porous metal based heat pipe evacuated tube solar collector: An experimental study. Solar Energy, 251, 106-118. DOI: https://doi.org/10.1016/j.solener.2022.10.054

Uniyal, A., Prajapati, Y. K., & Suman, S. (2023). Heat transfer and melting characteristics of the phase change material inside U-tube based evacuated tube solar collector. Journal of Energy Storage, 62, 106918. DOI: https://doi.org/10.1016/j.est.2023.106918

Voller, V. R., & Prakash, C. (1987). A fixed grid numerical modelling methodology for convection-diffusion mushy region phase-change problems. International journal of heat and mass transfer, 30(8), 1709-1719. DOI: https://doi.org/10.1016/0017-9310(87)90317-6

Shokouhmand, H., & Kamkari, B. (2013). Experimental investigation on melting heat transfer characteristics of lauric acid in a rectangular thermal storage unit. Experimental Thermal and Fluid Science, 50, 201-212. DOI: https://doi.org/10.1016/j.expthermflusci.2013.06.010

Nakhchi, M. E., & Esfahani, J. A. (2020). Improving the melting performance of PCM thermal energy storage with novel stepped fins. Journal of Energy Storage, 30, 101424. DOI: https://doi.org/10.1016/j.est.2020.101424