Effect of Coating Time of Electrophoretic Deposition of Hydroxyapatite-Chitosan-Magnesium Oxide Coatings on Ti-6Al-4V Alloys

Authors

  • Anees Kadhim Tayyeh Department of Materials Engineering, College of Engineering, University of Diyala, 32001 Diyala, Iraq.
  • Ahmed Hasan Department of Materials Engineering, College of Engineering, University of Diyala, 32001 Diyala, Iraq.

DOI:

https://doi.org/10.24237/djes.2025.18309

Keywords:

EPD, Ti-6Al-4V, metallic implants, composite coating

Abstract

This research aims to evaluate various coatings on titanium alloy substrates to increase corrosion resistance and surface quality. This involves coating the substrates with layers of Hydroxyapatite (HAP), Chitosan (CS), and Magnesium oxide (MgO) using the EPD technique. The cell voltage value was set to 5 V, while the coating time was set to 5, 10, and 15 min. SEM was used to measure the thickness of the cross-sectional coating layers, and it was also used to show the morphology of the composite coating. From the results 10-minute deposition time has been established as the most optimal to produce an even, thick, uniform, and dense coating with good mechanical properties. The thickness more than doubles with increases in time with the coat almost tripling at 15 minutes and 5 minutes respectively. EDX analysis showed that the elemental compositions of calcium, oxygen, and phosphorus increased after 15 minutes, indicating a dense coating. The research findings indicate that the adhesion force transitions to a marginally positive value of 0.05 nN, suggesting a weak attachment rather than a robust bond. Additionally, Young's modulus shows a significant decline to 3.93 MPa, which signifies a reduction in the stiffness of the material. The surface stiffness decreases to 0.19 nN/nm between 10 and 15 minutes, indicating a loss of rigidity. Although longer coating times may increase thickness, they can also reduce functionality and raise defect risks. This reinforces that electrophoretic deposition (EPD) effectively improves the alloy's surface quality for biomedical applications.

Downloads

Download data is not yet available.

References

[1] A. R. Boccaccini and J. H. Dickerson, "Electrophoretic deposition: fundamentals and applications," vol. 117, ed: ACS Publications, 2013, pp. 1501-1501.

[2] S. A. Batool, A. Wadood, S. W. Hussain, M. Yasir, and M. A. Ur Rehman, "A Brief Insight to the Electrophoretic Deposition of PEEK-, Chitosan-, Gelatin-, and Zein-Based Composite Coatings for Biomedical Applications: Recent Developments and Challenges," Surfaces, vol. 4, pp. 205-239, 2021.

[3] P. Bocchetta, L.-Y. Chen, J. D. C. Tardelli, A. C. d. Reis, F. Almeraya-Calderón, and P. Leo, "Passive layers and corrosion resistance of biomedical Ti-6Al-4V and β-Ti alloys," Coatings, vol. 11, p. 487, 2021.

[4] A. M. Khorasani, M. Goldberg, E. H. Doeven, and G. Littlefair, "Titanium in biomedical applications—properties and fabrication: a review," Journal of biomaterials and tissue engineering, vol. 5, pp. 593-619, 2015.

[5] M. B. Hussein, A. M. Mustafa, M. H. Abdulkareem, and A. Alamiery, "Comparative corrosion performance of YSZ-coated Ti-13Zr-13Nb alloy and commercially pure titanium in orthopedic implants," South African Journal of Chemical Engineering, vol. 48, pp. 40-54, 2024.

[6] M. B. Hussein, A. M. Mustafa, and M. H. Abdulkareem, "A Comparative Study on Dip Coating and Corrosion Behavior of Ti-13Zr-13Nb and Commercially Pure Titanium Alloys Coated with YSZ by Taguchi Design," Salud, Ciencia y Tecnología-Serie de Conferencias, vol. 3, pp. 847-847, 2024.

[7] A. K. Abed, A. M. Mustafa, and A. M. Resen, "Assessment Corrosion and Bioactive Behavior of Bioglass Coating on Co-Cr-Mo Alloy By Electrophoretic Deposition For Biomedical Applications," Corrosion Science and Technology, vol. 23, pp. 179-194, 2024.

[8] Y. Kirmanidou, M. Sidira, M.-E. Drosou, V. Bennani, A. Bakopoulou, A. Tsouknidas, et al., "New Ti‐alloys and surface modifications to improve the mechanical properties and the biological response to orthopedic and dental implants: A review," BioMed research international, vol. 2016, p. 2908570, 2016.

[9] M. Kaur and K. Singh, "Review on titanium and titanium based alloys as biomaterials for orthopaedic applications," Materials Science and Engineering: C, vol. 102, pp. 844-862, 2019.

[10] S. Rastegari and E. Salahinejad, "Surface modification of Ti-6Al-4V alloy for osseointegration by alkaline treatment and chitosan-matrix glass-reinforced nanocomposite coating," Carbohydrate polymers, vol. 205, pp. 302-311, 2019.

[11] X. Li, X.-Y. Ma, Y.-F. Feng, Z.-S. Ma, J. Wang, T.-C. Ma, et al., "Osseointegration of chitosan coated porous titanium alloy implant by reactive oxygen species-mediated activation of the PI3K/AKT pathway under diabetic conditions," Biomaterials, vol. 36, pp. 44-54, 2015.

[12] A. Arifin, A. B. Sulong, N. Muhamad, J. Syarif, and M. I. Ramli, "Material processing of hydroxyapatite and titanium alloy (HA/Ti) composite as implant materials using powder metallurgy: A review," Materials & Design, vol. 55, pp. 165-175, 2014.

[13] M. Dehestani, E. Adolfsson, and L. A. Stanciu, "Mechanical properties and corrosion behavior of powder metallurgy iron-hydroxyapatite composites for biodegradable implant applications," Materials & Design, vol. 109, pp. 556-569, 2016.

[14] J. Affi, O. Susanti, D. Juliadmi, D. Oktaviana, and M. Tauhid, "Effect of Bilayer Nano-Micro Hydroxyapatite on the Surface Characteristics of Implanted Ti-6Al-4V ELI," International Journal of Automotive and Mechanical Engineering, vol. 20, pp. 10777-10785, 2023.

[15] X. Ma, Y. Gao, D. Zhao, W. Zhang, W. Zhao, M. Wu, et al., "Titanium implants and local drug delivery systems become mutual promoters in orthopedic clinics," Nanomaterials, vol. 12, p. 47, 2021.

[16] E. Mahlooji, M. Atapour, and S. Labbaf, "Electrophoretic deposition of Bioactive glass–Chitosan nanocomposite coatings on Ti-6Al-4V for orthopedic applications," Carbohydrate polymers, vol. 226, p. 115299, 2019.

[17] X. Chen, S. Chen, L. Liang, H. Hong, Z. Zhang, and B. Shen, "Electrochemical behaviour of EPD synthesized graphene coating on titanium alloys for orthopedic implant application," Procedia Cirp, vol. 71, pp. 322-328, 2018.

[18] M. I. Hamil, M. A. Siyah, and M. K. Khalaf, "Electrophoretic deposition of Thin film TiO2 on Ti6AL4V alloy surface for biomedical applications," Egyptian Journal of Chemistry, vol. 63, pp. 2959-2964, 2020.

[19] D. Juliadmi, N. F. Nuswantoro, H. Fajri, I. Y. Indriyani, J. Affi, M. Manjas, et al., "The coating of bovine-source hydroxyapatite on titanium alloy (Ti-6Al-4V ELI) using electrophoretic deposition for biomedical application," in Materials Science Forum, 2020, pp. 97-106.

[20] P. Eshghinejad, H. Farnoush, M. Bahrami, H. Bakhsheshi-Rad, E. Karamian, and X. Chen, "Electrophoretic deposition of bioglass/graphene oxide composite on Ti-alloy implants for improved antibacterial and cytocompatible properties," Materials Technology, vol. 35, pp. 69-74, 2020.

[21] J. Affi, A. Sutanto, D. M. Putri, D. Juliadmi, N. F. Nuswantoro, H. Fajri, et al., "Adhesion strength of hydroxyapatite coating on titanium alloy (Ti-6Al-4V ELI) for biomedical application," in IOP Conference Series: Materials Science and Engineering, 2021, p. 012031.

[22] L.-C. Xu and B. E. Logan, "Interaction forces between colloids and protein-coated surfaces measured using an atomic force microscope," Environmental science & technology, vol. 39, pp. 3592-3600, 2005.

[23] B. Makurat‐Kasprolewicz and A. Ossowska, "Electrophoretically deposited titanium and its alloys in biomedical engineering: Recent progress and remaining challenges," Journal of Biomedical Materials Research Part B: Applied Biomaterials, vol. 112, p. e35342, 2024.

[24] S. W. Ibrahim, W. A. Al-Nakkash, and N. M. Al Ghaban, "Histological Assessment of Nano Hydroxyapatite, Chitosan and Collagen Composite Coating on Commercially Pure Dental Implants in Comparison with Nanohyroxyapatite Coating," Int J Sci Res, vol. 6, pp. 1920-3, 2017.

Downloads

Published

2025-09-01

How to Cite

[1]
“Effect of Coating Time of Electrophoretic Deposition of Hydroxyapatite-Chitosan-Magnesium Oxide Coatings on Ti-6Al-4V Alloys”, DJES, vol. 18, no. 3, pp. 136–147, Sep. 2025, doi: 10.24237/djes.2025.18309.

Similar Articles

1-10 of 620

You may also start an advanced similarity search for this article.